# NASys LoRaWAN Outdoor Gateway

> NASys LoRaWAN Outdoor Gateway is an 8 Channel LoRaWAN gateway.

Source: https://www.thethingsindustries.com/docs/hardware/gateways/models/nasysoutdoorgateway/


![NASys LoRaWAN Outdoor Gateway](https://www.thethingsindustries.com/docs/hardware/gateways/models/nasysoutdoorgateway/IX1001.png)


This page guides you to connect NASys LoRaWAN® Outdoor Gateway to The Things Stack.

NASys LoRaWAN Outdoor Gateway is an 8 Channel LoRaWAN gateway, whose technical specifications can be found in [the official product page](https://www.nasys.no/product/lorawan-gateway/).

## Prerequisites

1. User account on The Things Stack with rights to create Gateways.
2. NASys LoRaWAN Outdoor Gateway connected to the internet (or your local network) via ethernet.

## Registration

Create a gateway by following the instructions for [Adding Gateways](https://www.thethingsindustries.com/docs/hardware/gateways/concepts/adding-gateways/). Typically, the **EUI** field for your gateway should exist on the sticker at the bottom. Make note of the Gateway ID you choose, because it will be needed later.

## Configuration using a Terminal

Find the IP address the gateway. This can be done in various ways. You can connect your machine to the same local network as that of the gateway Ethernet connection and scan for open SSH ports or assign a static IP to the gateway and use that. Once the gateway IP address is found, ssh into it.

```bash
ssh root@<GatewayIP>
```

The default username is **root**, and the default password can be also found in the sticker.

Your gateway should come with a slightly modified version of the [Lora-net UDP packet forwarder](https://github.com/Lora-net/packet_forwarder) pre-installed at `/opt/nas-lgw`. There are two configuration files `global_conf.json` and `local_conf.json`, both located in `/opt/nas_lgw`.

The Gateway Configuration Server can be used to retrieve a proper `global_conf.json` configuration file for your gateway. Follow instructions [here]().

Update the configuration files on the gateway with your downloaded `global_conf.json` and restart the packet forwarder:

```bash
mv /opt/nas-lgw/local_conf.json /opt/nas-lgw/local_conf.json.old
cp global_conf.json /opt/nas-lgw/global_conf.json

systemctl restart nas-lgw
```

If your configuration was successful, your gateway will connect to The Things Stack after a couple of seconds.

## Troubleshooting

If the gateway does not connect to The Things Stack after a few minutes, issue a `reboot` command, or disconnect and reconnect the power supply to power-cycle the gateway.

If you still have trouble connecting to The Things Stack, then try editing the `gateway_conf` section:

```bash
vi /opt/nas-lgw/global_conf.json
```

Edit the server parameters:

- **gateway_ID**: Make sure this is the same as the GatewayEUI (in lowercase).
- **server_address**: Address of your The Things Stack deployment. See [Server Addresses](https://www.thethingsindustries.com/docs/concepts/server-addresses/).
- **serv_port_up**: UDP upstream port of the Gateway Server, typically 1700.
- **serv_port_down**: UDP downstream port of the Gateway Server, typically 1700.

You can access the gateway system logs using journalctl. See `journalctl --help` for details

```bash
journalctl -f -u nas_lgw -n 1000
```

The gateway logs will rotate when they reach about 15M in size, which means that you will generally not be able to access very old logs. At times of dense traffic (e.g. ~1000s of devices) this typically means that you will only have logs for 2-3 hours. If you want to keep historical data (for whatever reason), then you will have to forward the logs to an external server. If you decide to do so, then `netcat` may be useful:

```bash
journalctl -f | nc server-hostname server-port
```

